SAI – Safety analog input

Block SymbolLicensing group: ADVANCED
PIC

Function Description
The SAI block tests the input signal u and assesses its validity. The input signal u is considered invalid (the output E = on) in the following cases:

F1: Hardware error. The input signal HWF = on.
F2: The input signal u varies too little. The last nc samples of the input u lies within the interval of width du,
du = vmaxvmin 2nbits , for nbits {8,9,...,16} 0, for nbits{8,9,...,16},

where vmin and vmax are the lower and upper limits of the input u, respectively, and nbits is the number of A/D converter bits. The situation when the input signal u varies too little is shown in the following picture:

PIC

If the parameter nc is set to nc = 0, the condition F2 is never fulfilled.

F3: The input signal u varies too much. The last nr samples of the input u filtered by the SPIKE filter have a span which is greater than rate,
rate = pratevmaxvmin 100 ,

where prate defines the allowed percentage change in the input signal u within the last nr samples (with respect to the overall range of the input signal u vmin,vmax). The block includes a SPIKE filter with fixed parameters mingap = vmaxvmin 100 and q = 2 suppressing peaks in the input signal to avoid undesirable fulfilling of this condition. See the SPIKE block description for more details. The situation when the input signal u varies too much is shown in the following picture:

PIC

If the parameter nr is set to nr = 0, the condition F3 is never fulfilled.

F4: The input signal u is out of range. The last nv samples of the input signal u lie out of the allowed range vmin,vmax.

If the parameter nv is set to nv = 0, the condition F4 is never fulfilled.

The signal u is copied to the output y without any modification when it is considered valid. In the other case, the output y is determined by a substitute value from the sv input. In such a case the output E is set to on and the output iE provides the error code. The input R resets the inner error flags F1F4. For the input R set permanently to on, the invalidity indicator E is set to on for only one cycle period whenever some invalidity condition is fulfilled. On the other hand, for R= off, the output E is set to on and remains true until the reset (rising edge Roff on).

The table of error codes iE resulting from the inner error flags F1F4:






F1 F2 F3 F4 iE





0 0 0 0 0
0 0 0 1 1
0 0 1 0 2
0 0 1 1 3
0 1 0 0 4
0 1 0 1 5
0 1 1 0 6
0 1 1 1 7
1 * * * 8





The nb parameter defines the number of samples which are not included in the validity assessment after initialization of the block (restart). Recommended setting is nb 5 to allow the SPIKE filter initial conditions to fade away.

Inputs

u

Analog input of the block

Double (F64)

sv

Substitute value to be used when the signal u is marked as invalid

Double (F64)

HWF

Hardware error indicator

Bool

off ..

The input module of the signal works normally

on ...

Hardware error of the input module occurred

R

Reset inner error flags F1F4

Bool

Outputs

y

Analog output of the block

Double (F64)

yf

Filtered analog output signal y, output of the SPIKE filter

Double (F64)

E

Output signal invalidity indicator

Bool

off ..

Signal is valid

on ...

Signal is invalid, y = yf = sv

iE

Reason of invalidity

Long (I32)

0 ....

Signal valid

1 ....

Signal out of range

2 ....

Signal varies too little

3 ....

Signal varies too little and signal out of range

4 ....

Signal varies too much

5 ....

Signal varies too much and signal out of range

6 ....

Signal varies too much and too little

7 ....

Signal varies too much and too little and signal out of range

8 ....

Hardware error

Parameters

nb

Number of samples which are not included in the validity assessment of the signal u after initialization of the block  10

Long (I32)

nc

Number of samples for invariability testing (the F2 condition)  10

Long (I32)

nbits

Number of A/D converter bits  12

Long (I32)

nr

Number of samples for variability testing (the F3 condition)  10

Long (I32)

prate

Maximum allowed percentage change of the input u within the last nr samples (with respect to the overall range of the input signal vmaxvmin)  10.0

Double (F64)

nv

Number of samples for out-of-range testing (the F4 condition)  1

Long (I32)

vmin

Lower limit for the input signal u  -1.0

Double (F64)

vmax

Upper limit for the input signal u  1.0

Double (F64)

2023 © REX Controls s.r.o., www.rexygen.com